2020-2025 Jeep Gladiator JT Rear Bumper LED Reverse Lights | 1,500 Lumens

Nice product to add to our Gladiator. Pretty straightforward installation. Definitely recommend buying the harness as for me splicing wires just may cause issues later on.

I really like these reverse lights. They light up the area so you can see where you're going. It also makes sure people behind you can tell you are in reverse.

My first ORACLE purchase, install was super easy and fast. Looks factory, super bright. I would recommend this product to anyone!!!!

Great Lights!!!! Very Bright!!!! Never any issues seeing at night.

Installed these on my 2023 Gladiator Willys, and they have a nice fit and finish, and absolutely compliment the taillight reverse lights; making it much brighter when backing up.

I have installed these back up lights on my JLU Rubicon Recon, my wife’s JLU Rubicon 392 and now on our JT Gladiator Mohave. It’s a in expensive upgrade that actually works well and is very functional. As a retired Reginol manager for 4WPW and custom shop owner I highly recommend them. They are easy to install, look and work great.

Installed these over the wknd and they are super bright! Shoots light well behind the truck and will provide line of sight in low lit situations at night.

Install was easy, especially with OEM harness included for left tail light. One screw on each side is a little tedious but thats on Jeep.

I was eyeballing these for the last four months ever since I bought my Rubicon. I finally jumped a gun during Black Friday sales and saved some money. So if money is tight, wait until you can catch a good sale and you’ll definitely be in a position to get these. I know that the plug-in harness is something that works for several people, but unfortunately it did not work out for me. They sent me a replacement under warranty, and I ran into the same issue. I did some troubleshooting on my own and found out that once I put the Wires onto my trailer 7pin, I didn’t have any issues. I was running into problems when I plugged in the tail light harness. The tail lights were functioning, but they were not functioning properly at all. Another thing to keep in mind, the Oracle lights were working immediately. It was just the jeeps lights I was having issues with. Oracle sent out the replacement immediately. I did not have to jump through any hoops to get it. I didn’t have to wait more than three days to receive it. So that was nice. But since I had a little bit of bad luck, I ran into the same issue again. After a little research, I found out that Oracle sells a trailer, wiring harness, that essentially does the same thing as the tail light plug-in play harness. I suggested that we go that route and they obliged. I’m sure it’s a case by case basis, but my situation was unique. It got to the point where they were going to be sent back or they were going to send me the new harness. Since they opted for the trailer harness, everything is working perfect. Knock on wood that it stays that way. In my humble opinion, even if you don’t want to buy the trailer harness, I would tap into the existing wiring just because it’s that much easier. Save a few bucks. I highly suggest buying this product. I would buy again.
Cincinnati
Installation – extremely easy. Even if you have very limited skills in this department, you’ll be able to understand how to install these by watching a YouTube video. It took me five minutes. I bet it wouldn’t take somebody longer than a half an hour.

Fitment- doesn’t get any better. Completely flush and exactly the same size and shape as the reflectors that were there prior. These lights also have a built-in reflector so for the folks out there who are all about safety, this will fit the bill for you.

In case anybody was wondering, the tailgate light bar is for well-known company on Amazon. Just search “triple LED tailgate light bar with sequential turn signals” and it should show up.

I got these for my wife’s 23 Gladiator Overland. I looked at the installation instructions and decided that I would not install them. I oversaw the installation by my 14 year old daughter. I’m trying to teach her to do easy stuff, and this DEFINITELY fit the bill. No problems on the install, the plug and play adapter is EXACTLY the size it needs to be, as long as you route it properly. I went back and added a few more zip ties, but I’m a firm believer in overkill.
So far they are FANTASTIC. I got these because have the flush mount tail lights on my 2-door JL Rubicon Wrangler and the reverse lights on that are also FANTASTIC. I’ll see how these work out, then maybe put flush mount and the Racetrack Tailgate Panel on it too. My daughter is asking if they make anything for her JK.
All in all, very happy with all their stuff.
I would, and I have, recommended these to others.

Love them. Think they look better as well as great functionality. I do like that they still have the small reflectors but I do with they functioned as extra brake lights

Product is top notch. Stock reverse lights even on Mojave X are subpar. Especially in rain! Got the harness which made it super easy and as professional as possible. Upper screws a bit of a challenge but overall took me about 60 minutes because video doesn’t give enough guidance on removing taillights. Had to find another video so I didn’t mess up.

Highly recommend

Just easy as pie. Make sure to get the kit that is plug and play so you dont have to cut into your wiring. Very bright and a great help at night. The hard part was actually just removing the left jeep tail light. Pull straight back after removing the two screws. Put some silicone grease on the grommets so next time the tail light removal will be easy. Summit Racing carries these in stock.

Installed these to be powered by auxiliary switch #4 in my Gladiator. I previously had installed a 12 volt socket in the bed of the truck, using 2 wires (one hot and one ground) run to the engine compartment. When I installed these lights, I converted the dedicated ground for the 12 volt socket to a hot wire for these bumper lights. I picked up a chassis ground (for both items) under an existing screw in the frame. Works great and saved me from running new wires.

Found these lights and ordered. Install was super easy! Even impressed my wife that the reflector is replaced by a working BRIGHT reverse light! 👍

These feel like they're very high-quality construction. They appear well-sealed and have a nice heat sink on the back side. Installation was quick and easy, and they project a lot of light - almost too much light! They are so bright they kindof blow out the sensor on the back-up cam when you're close to another object.

I got the ORACLE Lighting Rear Bumper LED Reverse Lights for Jeep Gladiator JT with the plug and play cable and the ORACLE Lighting Flush Mount LED Tail Lights for Jeep Gladiator JT.

It's like having a set of headlights in the rear!
The set up is awesome and was easy to install.

Now I just have to figure out how to shut off the license plate lights when I shift into reverse!

Great product especially at night can see alot more objects when backing up aslo I think in the daytime also people seem to notice when backing up as well.

Replaced bumper reflectors with Oracle Lighting Rear Bumper LED Reverse Lights. I was very easy to do. I took longer to tie wrap the wires than to replace the lights.

Justin was very helpful with an unrelated question concerning tire type and size in one of the pictures they had of their vehicle in the picture section. Justin sent out a picture along with Tire Manufacture and size.

Thank you again.

I would have added pictures but I figured there were enough of the rear view of the Gladiator and lights.

High quality product and very well constructed!

I know some people including myself have had trouble getting these lights to work. Some Gladiators respond differently. There is a simple solution, Grab yourself a Putco trailer harness adapter #529004. This will allow you to connect your New Oracle reverse lights with ease and also allow you to add a tail gate light bar too!
All without cutting the factory wiring.

Now my truck looks awesome. I also have the Oracle tail lights and love them.

When I ordered these lights there were on a long back order. Received and installed the same day. They are awesome! The quality is outstanding, perfect fit and finish. Great lighting. I strongly suggest using the plug-in-play harness, makes things so much easier and quicker, we all know the clamp-on wire-taps are sometimes sketchy. With the plug-in-play all there is to do is remove only the driver's side tail light assembly (2 screws and pull straight back from the truck) unplug the original harness and plug in the new one. That quick! Push the tail light assembly back into position and replace the two screws, done.

At first I thought there would not be enough wire to go to the passenger's side. I was wrong it is a perfect length. Wire tie to existing wires along the rear of the bumper and you're done.

I also ran into the issue of the bumper trim screw being in the way. I didn't remove the screw I just kept working at it with a 7mm short socket and was able to get it done.